Did you know that the fastest and easiest way to keep your commercial hard floors sparkling like new is to use an auto scrubber? Well, it turns out that it’s true! With the right know-how, you can make quick work of dirty floors and keep them looking their best. Read on to learn how to get the most out of your auto scrubber!
Contents
Prep the Area
When prepping an area to be cleaned with an auto scrubber, it is important to start by removing any large debris such as sticks, stones, leaves, or large chunks of dirt. Use a broom, vacuum cleaner, dustpan, and brush to remove the debris.
Once this has been done, the area can then be swept thoroughly with either a mop or floor scrubber attachment to pick up any remaining small particles. Make sure you go over the entire surface paying extra attention to any areas which have higher levels of wear and tear, as well as corners or areas like aisle ways that may have small amounts of build-up over time.
Once the area looks clean and all grit has been removed either use a wet/dry vacuum to extract any moisture left on the floor and ensure that it is completely dry before continuing.
Dust Mop or Vacuum Floors
Before attempting to use an auto scrubber on commercial hard floors, it is important to dust mop or vacuum them beforehand. This will remove loose dirt and debris, preparing the floors for the auto scrubber’s more intensive scrubbing process. Using a broom is also an effective way to get rid of any caked-on dirt and grime. Make sure to sweep side-to-side and then front-to-back for maximum effectiveness. To avoid leaving any residue behind, sweep towards a dustpan rather than around it. After completing this task you can move on to the auto scrubber cleaning process.
Prep the Machine
When you are ready to begin cleaning your hard floors with an auto scrubber, you must first prep the machine. You can start by using the manufacturer’s manual to familiarize yourself with the machine’s features. You will need to check for proper equipment and supplies such as adding the scrubbing solution, charging up your battery, and ensuring that all filters, brushes, and hoses are securely connected.
Next, make sure the scrubber has been filled according to directions and that it is correctly balanced in order to create optimum cleaning performance. Use a damp cloth or vacuum cleaner to remove any dust or dirt that has been collected on your machine before starting. Test drive the machine in a small area of your facility if possible so you can practice moving it forward and backward before starting on a larger task.
Scrub the Floors
Scrubbing your commercial hard floor surfaces is an essential part of keeping them clean and free from germs and dust particles. The most effective way to ensure that your floors are thoroughly cleaned is to use an auto scrubber. An auto scrubber is a device with a brush attachment that us used to move over and clean floors with the help of detergents or cleaning products.
Using an auto scrubber requires some preparation in order to ensure that you are able to use the device properly, securely, and safely. Before using your auto scrubber, you need to make sure that the hard floors you intend to clean are properly prepared by sweeping them first, then mopping if necessary so that they are free from any loose dirt and debris. You should also follow all steps provided in your machine’s instruction manual before plugging it in and starting the cleaning process.
Once your hard floors have been adequately prepared for cleaning, it’s time to begin using your auto scrubber. Start by carefully pushing it onto the floor surface while applying just enough pressure so that it can properly attach itself – too little pressure may cause weak suctioning performance due to improper operation of the brushes – but don’t push too hard as this may scratch or damage delicate surfaces such as wooden floors or tiles!
Move slowly over the surface of your floor according to the manufacturer’s suggestions for optimal cleaning; go back and forth slowly in a straight line for best results, avoiding sharp turns which could cause damage. After completing one section, pull back slightly on the handle before continuing on to the next section – this will help move any trapped dirt away from where you had just been scrubbing! When finished with one area of the room, empty any collected materials from your machine’s tank and repeat as necessary until all floors have been cleaned.
Drain the Auto Scrubber Tanks
Before using your auto scrubber on your hard floors, you must make sure the tanks are clean and properly drained. If the tanks are not adequately drained, you can risk leaving debris in the scrubber solution or rinse water, which can damage your floors.
To ensure maximum suction power and ensure a clean surface on your hard floors, you’ll need to clear out any dirt or debris that has been collected in the tank. To do this, open up the brushes and use a soft-bristle brush to loosen up any trapped particles, then empty out the material into a trash bin or dispose of it properly.
Once all of the dirt and debris have been cleared out of the tanks, you can turn off your auto scrubber and open both tanks to drain out any excess solution that may be contained in them. When both tanks have been emptied and their contents applied to your flooring through cleaning processes, be sure to re-close and secure them prior to disposing of any remaining cleaner residue. This will prevent any spillage which could damage hard-maintained surfaces.
Rinse the Auto Scrubber Tanks
Before you use your auto scrubber for floor cleaning, you should rinse the tanks. Most modern auto scrubbers have two tanks: one for clean water and one for used or dirty water.
- Fill the clean water tank with a cleaning solution recommended by the manufacturer or according to the needs of your particular application.
- Empty and rinse out the used-water tank to prevent cross-contamination of chemicals and dirt between floors. Be sure you’re aware of any local restrictions detailing waste disposal requirements; some municipalities may require specialized chemicals in order to dump certain types of liquids safely.
- Finally, inspect both tanks to ensure they are free from any obvious defects that might cause an accident or injury later on.
Leave the Tanks Open to Dry
When you finish scrubbing your floors with your auto scrubber, it is important to always leave the tanks open to dry. This allows moisture from the tanks and from the cleaning solution to evaporate properly and prevents mold, mildew, and bacteria from forming on the surfaces. Leaving the tanks open also prevents corrosion of any metal parts inside and ensures that no water remains in the tanks, which can become a breeding ground for bacteria.
Additionally, by leaving the tanks open after each use, it can ensure that you extend their life and help keep your auto scrubber performing optimally.
Clean the Squeegee
When cleaning your commercial hard floors, the first step is to clean the squeegee. A squeegee consists of two components; a rubber blade that is attached to a handle. The rubber blade helps to remove soil from the surface of your hard floor, while the handle allows you to control the movement of the squeegee during cleaning.
To clean your squeegee, follow these steps:
- Remove any debris or dirt from the rubber blade and handle using a brush or cloth.
- Spray an all-purpose cleaner onto both components and allow time for it to penetrate any built-up grime and dirt.
- You can scrub either part by hand using a bristled brush or towel if necessary.
- Rinse off all components thoroughly with water and then dry with a soft cloth or towel before use.
- Once it is clean, store your squeegee in an area where it will not be exposed to dirt or moisture which could affect its condition over time.
Hire Professional Cleaners to Clean for You
For those who don’t have time or the know-how to learn how to use an auto scrubber, it’s possible to hire professional cleaners instead. Professional cleaners are capable of providing a deeper cleaning to your floor than most domestic machines can achieve. They will also be able to select the best products and equipment for your floors, guaranteeing a perfect result.
Professionals also come with vast experience in commercial cleaning and can offer advice on how best to maintain and protect your floors. This is especially important for hard floor surfaces, which require more upkeep than carpeted ones. Depending on the type of floor you have and its particular needs, a professional cleaner may recommend:
- Specific product types for cleaning.
- Different methods for buffing and polishing.
- Specific maintenance procedures need to be followed.
Frequently Asked Questions
What type of auto scrubber should I use to clean my commercial hard floors?
You should use a walk-behind auto scrubber with a cylindrical brush or disk that can scrub your commercial hard floors. This type of auto scrubber is designed to clean large areas quickly and efficiently.
How do I use an auto scrubber?
To use an auto scrubber, first, fill the tank with the appropriate cleaning solution. Then, turn the machine on and push it back and forth across the floor. Be sure to overlap each pass to ensure complete coverage of the entire floor. When finished, turn the machine off, empty the tank, and rinse the floor with clean water.
How often should I use an auto scrubber to clean my commercial hard floors?
You should use the auto scrubber to clean your commercial hard floors at least once a week, depending on the amount of foot traffic. For high-traffic areas, you may need to clean more frequently.
Conclusion
At the end of the process, it’s important to dispose of used water and dispose of or store cleaning solution correctly. Once all of your hard floors have been cleaned, take a moment to inspect your premises for any areas needing additional attention. Afterward, your floor will be ready for normal traffic.
If you experience any difficulty while operating an auto scrubber, be sure to refer to the owner’s manual or contact an authorized service technician for further advice. With proper care and maintenance, an auto scrubber can offer a cost-effective way to keep your commercial hard floor clean and inviting for many years to come.