Are you searching for the best way to clean your trusty top-load washing machine? Well, never fear! We have all the tips and tricks you need to give your washing machine a deep clean that’ll make it look new. So grab your cleaning supplies and let’s get started!
Contents
Wipe Down the Outside of the Machine
To keep your washing machine looking its best and operating correctly, it’s important to clean the outside of the machine regularly. Begin by wiping down the exterior of the machine with a warm, damp cloth. Make sure all dirt and debris are removed from any visible crevices and focus on hard-to-reach areas such as underneath handles or around the control settings.
After you have done this, you should use a soft brush or vacuum hose to gently remove any lint that may have collected on the outside of your machine. If you encounter any stubbornly stuck-on grime, try scrubbing it lightly with an old toothbrush before wiping it away with a damp cloth.
If you are in the Cheras area, hiring a cleaning specialist to help keep your washing machine in top condition is recommended. They have the proper tools and equipment for the job and will save you much time and effort.
Fill the Machine With Hot Water and Vinegar
Cleaning a top-load washing machine can be a simple and effective way to keep your laundry equipment running like new. Start by filling the machine with hot water and then add a vinegar solution. This will help to clean any residues that have built up in the washer drum, leaving it fresh and odor-free. You can adjust the amount of vinegar you use depending on your particular make and model, but for most machines about one cup should be sufficient.
Let the solution sit for about 20 minutes, during which time any sediment or buildup will be lifted from the interior surface of the washer drum.
Run a Full Wash Cycle
Using a high-efficiency top-load washing machine is a great way to keep your laundry clean and sparkling. To keep your machine performing at its best, you should periodically clean it. One of the most effective ways to do this is by running a full wash cycle with a special cleaning solution, such as baking soda or white vinegar.
Start by filling the washer with hot water and adding either one cup of baking soda or 1/2 cup of white vinegar to it. Close the lid and turn on an extended cycle that can reach temperatures over 140°F (approximately 60°C). This will help dissolve residue, kill any germs, and remove soap scum, and mildew.
Once the wash has finished, you can open the lid again — but be careful not to get burned from any steam that is being released. Allow the interior of the machine to dry completely before putting in any new laundry items.
Wipe Down the Inside of the Machine
To keep your washing machine looking and smelling fresh, it’s important to clean both the inside and outside of the machine regularly. Wiping down the inside of the machine is the first step.
Start with a damp cloth and wipe down any visible residue on the tub walls. If there is a residual laundry detergent film, fill a spray bottle with water and white vinegar, then spritz it onto affected areas and let it sit for several minutes before wiping it away. If necessary, use an old toothbrush to help loosen any tough spots of dirt or grime.
Once you are done wiping away all of the dirt, spray another layer of your vinegar-water all-purpose cleaner onto the tub and then wipe it away with a dry microfiber cloth. This will help ensure that any lingering residue is removed from your washing machine’s interior surfaces.
Scrub Away Dirt and Grime
Before you start scrubbing your top-load washing machine, it’s important to give the outside of the machine a good cleaning. This will help remove dirt and debris that could potentially cause clogs or other problems. To do this, use a soft cloth and some liquid dish soap. Once you’ve finished wiping down the outside of the machine, move on to scrubbing away any dirt inside the drum or elsewhere.
The best way to clean your top-load washing machine is with a solution of baking soda and white vinegar. Start by pouring 1/4 cup of baking soda (about half a box) into the washer and running it through one cycle on its highest setting. Then fill with 1/2 cup of white vinegar and run another cycle on its highest setting as well. This should disinfect as well as help wash away any residue left behind from your cleaning solution.
For any tougher grime or stains, try using an all-purpose cleaner such as Scrubbing Bubbles Wipes or a bathroom cleaner for spot cleaning before running through another empty cycle on its highest setting using 1/4 cup of baking soda in place of bleach or detergent if desired. You should be sure to check all inside parts such as seals, hinges, lint traps, etc., for signs of wear and tear before use so you can follow up with proper maintenance if needed. Finally, don’t forget to wipe down your washer’s surfaces afterward with a damp cloth when done!
Wipe Down the Control Panel and Buttons
The control panel and the exterior buttons of your top-load washing machine should be wiped clean with a damp cloth or sponge. Be sure to avoid getting any water inside the buttons. If necessary, use a mild detergent or soap to assist in removing any visible dirt, grime, or residue. Allow to dry completely before pressing any buttons on the machine.
You can also use a vacuum cleaner with an upholstery attachment to gently remove dust from crevices and other hard-to-reach places. Finally, the manufacturer’s instructions may provide specific recommendations for cleaning plastic surfaces, so it’s advisable to consult them if you have questions.
Dry the Inside and Outside of the Machine
After cleaning the inside and outside of the washer, you should dry both to prevent any mildew from forming. Use a dry, soft cloth to wipe away any remaining residue on the outside of the machine. Once all surfaces are clean, make sure to dry off any water that was left behind by wiping with a soft, absorbent towel. Do not air dry as this could lead to fuzz or lint build-up on the surfaces that could reduce efficiency and damage your machine.
Inside the machine, open every hatch and door and use a soft rag or cloth to dry off any remaining moisture or excess detergent. Doing so will minimize mildew growth in hard-to-reach areas such as crevices or behind dispensers, keeping your machine clean and lasting longer.
Conclusion
Once you have completed your cleaning process, it is important to run a few cycles of clean water through your washing machine. This will help to further remove any residue and prevent the build-up of bacteria or mold.
Taking the time to regularly clean and maintain your top-load washing machine can help extend its useful life. Most importantly, it helps ensure that your laundry is as hygienic and free from dirt and germs as possible. By following these simple instructions, you can make sure that your washing machine works at peak efficiency every time you use it.